Märklin 74030 (HO) Center Rail Insulators (C Track)
Gauge H0 - Article No. 74030
Center Rail Insulators for Märklin and TRIX C-track
To separate power circuits or signal blocks. 8 pieces for 4 insulation points.
TRIX C-track (Code 83) is easy to set up, mechanically sturdy, and able to take rough treatment. On the other side, it is realistically detailed for advanced model railroaders, reliable and foolproof. The track geometry and extensive selection of turn-outs, curves and lengths allow you to build the most complexed lay-outs modelling the real world. Nevertheless, the real asset of this track is the play value. You can click-it together and take it apart as many times as you like. This is perfect for children or the experienced modeler that desire to improve and expand the lay-out. The C-track use a very strong connector mechanism under the roadbed which also includes the power connection. This system is far more reliable and provides better power conductivity than rail-joiners (which also are not used in the real world). The C-track is with its features smoother and more realistic, but you can transition to or from other track including flex track with the Adapter Track found in the TRIX C-track assortment.
There are 49 products.
Gauge H0 - Article No. 74030
Center Rail Insulators for Märklin and TRIX C-track
To separate power circuits or signal blocks. 8 pieces for 4 insulation points.
This feeder wire set has spade connectors for C Track. The set has two-conductors with a red and a brown wire. Length 1 meter / 39".
The 74040 feeder wire is not suitable if interference suppressor is required. If so yo may use the 74046 Feeder wire set with interference suppressor.
For retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free LEDs.
This is for retrofitting 2 C Track turnouts. The turnout lanterns can be used right, left, or three-way turnouts. They can be used with a manual hand lever and/or with the 74491 electric turnout mechanism. The lights for the lanterns are maintenance-free warm white LEDs.
This electric mechanism can be installed and connected on turnouts very easily without special tools. The mechanism sits hidden in the roadbed; below-baseboard mounting is not required. It is encapsulated against dirt and is protected against overloads with the end shut-off contacts. The mechanism can be controlled by means of a normal accessory controller, an accessory controller with a feedback function, or a digital decoder. The hand lever can be left on the turnout for manual control.
Gauge H0 - Article No. 74990
Track Screws for Märklin and TRIX C-track
For mounting C Track. 1.6 x 13 mm / 1/16" x 1/2" with cross point head. Contents 200 pieces.
These spade connectors can be used for the contact fingers on C Track. They are for all Märklin wire from 0.19 sq. mm / 0.0003 sq. in. or 0.02 in. diameter to 0.75 sq. mm / 0.001 sq. in. or 0.04 in. diameter. 1 package contains 20 spade connectors.
Märklin System C-Track | Light Mast for the Uncoupler Track
The light mast can be plugged into the Märklin 24997 C Track or TRX 62997 C-track (DC). The mast signal lights up when the uncoupler track is activated. Metal mast. Height 85 mm / 3-38". This light mast is technically the same as the earlier 5113 mast.
Motor brushes for older style motors requiring one carbon and one copper brush. E600300 includes 10 pairs.
This set is the ideal way to start out in Digital Control (DCC and mfx). It includes a Trix Mobile Station control system which is easy to use in both DCC and mfx. If you are using locomotives with mfx protocol the controller will automatically recognize and load the profile of the locomotive (Name, Class, Icon, Address, Function buttons and more). All you need to do is place the locomotive on the track. In DCC mode you have full control of the CVs and can build and store your own locomotive profile. Up to 40 profiles can be stored for direct access.
This set can be expanded with the Trix C Track extension sets and with the entire Trix C Track program
Code 83: The rail profile is 2.1 mm / 0.083" high
Trix H0 C-track - Article No. 62001
Straight Track
Snap-in end piece for the Trix C Track roadbed. For the end of a train line, sidings, display bases, and display cases. Length 16.5 mm / 5/8". 10 pieces in a package.
Trix H0 C-track - Article No. 62064
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 64.3 mm / 2-9/16". This track is the same length as the parallel track spacing for the wide radius turnouts and wide angle crossings
Trix H0 C-track - Article No. 62071
Straight Track - each
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 70.8 mm / 2-13/16". Removable roadbed slope. This track is used on both branches of the wide radius turnouts and wide angle crossings.
Trix H0 C-track - Article No. 62077
Straight Track - each
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 77.5 mm / 3-1/16"
Trix H0 C-track - Article No. 62077
Straight Track - 10pk
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 77.5 mm / 3-1/16"
Trix H0 C-track - Article No. 62094
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 94.2 mm / 3-3/4"
Trix H0 C-track - Article No. 62107
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 360 mm / 14-3/16", curve 7.5°
Trix H0 C-track - Article No. 62115
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 360 mm / 14-3/16", curve 15°
Trix H0 C-track - Article No. 62130
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 360 mm / 14-3/16", curve 30°
Trix H0 C-track - Article No. 62172
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 171.7 mm / 6-3/4"
Trix H0 C-track - Article No. 62188
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 188.3 mm / 7-3/8"
Trix H0 C-track - Article No. 62206
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 437.5 mm / 17-1/4", curve 5.7°. Extends turnout branch curves (62611 and 62612) to 30°
Trix H0 C-track - Article No. 62207
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 437.5 mm / 17-1/4", curve 7.5°
Trix H0 C-track - Article No. 62215
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 437.5 mm / 17-1/4", curve 15°
Trix H0 C-track - Article No. 62224
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 437.5 mm / 17-1/4", curve 24.3°. Same as turnout branch (62611 and 62612). This track piece will offset the curve on the turnout to parallel your track.
Trix H0 C-track - Article No. 62229
Straight Track - each
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 229.3 mm / 9". Serves as the complement to the length of the complementary curve on the wide radius turnouts and wide angle crossings.
Trix H0 C-track - Article No. 62230
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 437.5 mm / 17-1/4", curve 30°.
Trix H0 C-track - Article No. 62236
Straight Track - each
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 236.1 mm / 9-5/16". This track is the same length as the length of the wide radius turnouts.
Trix H0 C-track - Article No. 62315
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius R3 = 515 mm / 20-1/4" / 15°. Removable roadbed slopes. This track section is required on both branches of the 62771 and 62772 wide radius curved turnouts.
Trix H0 C-track - Article No. 62330
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 515 mm / 20-1/4", curve 30°
Trix H0 C-track - Article No. 62430
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius R4 = 579.3 mm / 22-13/16"
Trix H0 C-track - Article No. 62530
Straight Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius R5 = 643.6 mm / 25-5/16"
TRIX C-track HO Code 83
Left Turnout
Length 188.3 mm / 7-3/8", curve 24.3°, radius 437.5 mm / 17-1/4" (R2).
Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.
TRIX C-track HO Code 83
Right Turnout
Length 188.3 mm / 7-3/8", curve 24.3°, radius 437.5 mm / 17-1/4" (R2).
Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.
Length 188.3 mm / 7-3/8", crossing angle = 24.3° curve, radius 437.5 mm / 17-1/4" (R2).
Code 83: The rail profile is 2.1 mm / 0.083" high
The double slip switch comes with a manual hand lever, an electric mechanism and a lighted turnout lantern. A turnout decoder can be retrofitted. The double slip switch can be used for left or right installation. The setting for the branch or straight is well-defined. Built-in electric turnout motor and lantern.
TRIX C-track HO Code 83
Left Turnout
Inner curve 30°, radius 360 mm / 14-3/16" (R1). Outer curve 30° in the parallel curve spacing of 77.5 mm / 3-1/16"
Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.
TRIX C-track HO Code 83
Right Turnout
Inner curve 30°, radius 360 mm / 14-3/16" (R1). Outer curve 30° in the parallel curve spacing of 77.5 mm / 3-1/16"
Manual hand lever included. Can be retrofitted with a turnout mechanism, a digital decoder and turnout lanterns.
Length 236.1 mm / 9-5/16".
Branch track radius 1,114.6 mm / 43-7/8".
Turnout curve 12.1°.
10° metal frog, can be polarized.
Two (2) no. 62071 track sections are required at the end of the turnout. A roadbed piece to fit is included. A hand lever is included.
The 62912 curved track (radius 1,114.6 mm, 12.1°) is required to offset and parallel the branch track.
The 62229 straight track (229.3 mm) is required to offset the length of 62912 on the main track.
Length 236.1 mm / 9-5/16".
Branch track radius 1,114.6 mm / 43-7/8".
Turnout curve 12.1°.
10° metal frog, can be polarized.
Two (2) no. 62071 track sections are required at the end of the turnout. A roadbed piece to fit is included. A hand lever is included.
The 62912 curved track (radius 1,114.6 mm, 12.1°) is required to offset and parallel the branch track.
The 62229 straight track (229.3 mm) is required to offset the length of 62912 on the main track.
Trix H0 Code 83 - Article No. 62771
Left Wide Radius Curved Turnout
A long-standing wish of Trix fans is being fulfilled with the wide radius curved turnouts. Prototypical track plans are now no longer a problem. Trix is thereby setting a new standard in turnout geometry in which the conception of elegant track patterns reaches new dimensions
Inner curve: R3 = 515 mm / 20-1/4" / 30°.
Outer curve: 30° with a parallel curve spacing of 64 mm / 2-1/16".
Hand lever included.
Two (2) each 62315 track are required on the inner and outer curve of the turnout. A roadbed piece to fit here is included with the 62315.
The frog is metal and can be polarized.
The 74491 electric turnout mechanism, the 74462 digital decoder, and the 74470 turnout lanterns can be installed on this turnout.
Trix H0 Code 83 - Article No. 62772
Right Wide Radius Curved Turnout
A long-standing wish of Trix fans is being fulfilled with the wide radius curved turnouts. Prototypical track plans are now no longer a problem. Trix is thereby setting a new standard in turnout geometry in which the conception of elegant track patterns reaches new dimensions
Inner curve: R3 = 515 mm / 20-1/4" / 30°.
Outer curve: 30° with a parallel curve spacing of 64 mm / 2-1/16".
Hand lever included.
Two (2) each 62315 track are required on the inner and outer curve of the turnout. A roadbed piece to fit here is included with the 62315.
The frog is metal and can be polarized.
The 74491 electric turnout mechanism, the 74462 digital decoder, and the 74470 turnout lanterns can be installed on this turnout.
TRIX H0 Code 83 - Article No. 62900
C Track - Large Track Extension Set
This track extension set can be used to expand the track layout for all starter sets. It can be used for parallel track connections, passing sidings, a storage siding, and new routes. This track extension set is suitable for TRIX starter sets as well as for existing layouts. It can be expanded with the entire C Track program.
TRIX H0 Code 83 - Article No. 62902
C Track - C2 Extension Set - passing siding
For expanding the basic oval C Track starter set or any lay-out in need to include a passing siding.
TRIX H0 Code 83 - Article No. 62903
C Track - C3 Extension Set - passing siding with curved turnouts
For expanding the basic oval C Track starter set or any lay-out in need to include a passing siding utilizing curved turnouts to optimize available real-estate.
You may further expand your lay-out utilizing suitable pieces from the TRIX C-track assortment
Trix H0 C-track - Article No. 62912
Curved Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Radius 1114.6 mm / 43-7/8". Curve 12.1°
Complementary curve for the wide radius turnouts. Also suitable for use in constructing sweeping main lines.
This curve is used to offset the curve on the 62711 and 62712 Wide Radius Turnouts so that the branch will parallel with the main line. The 62071 is also required as a wedge piece between the turnout and the 62912.
Trix H0 C-track - Article No. 62922
Straight Track - Adapter Track from Fleishmann Profi Track (Code 100)
Code 83: The rail profile is 2.1 mm / 0.083" high (TRIX C-Track)
Length 180 mm / 7-7/8"
This track enables the transition from the FLEISCHMANN* Profi Track System to the Trix C Track: Code 100 to TRIX C-track Code 83
*FLEISCHMANN is a brand of Modelleisenbahn München, Inc.
Trix H0 C-track - Article No. 62977
Straight Track - Track End with a Bumpter
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 80.5 mm / 3-3/16"
A frame with a buffer beam comes mounted on the track. The rails end in the roadbed.
Trix H0 C-track - Article No. 62997
Straight Track - Uncoupler Track
Code 83: The rail profile is 2.1 mm / 0.083" high
Length 94.2 mm / 3-3/4"
The uncoupler track comes with a manual hand lever and a built-in electric mechanism. It is compatible with most common European coupler systems. It can be used with all NEM couplers and with current close coupler systems. A light mast can be plugged into the uncoupler track as an uncoupler signal (Märklin 74997). The uncoupler track can be connected to a control box or to a digital decoder
TRIX H0 Code 83 - Article No. 66861
C Track - Turntable
This is a DB standard design 23 meter / 74 foot 9 inch turntable. It is designed for conventional and digital locomotive operation. The remote controlled deck has a built-in motor. It can only be controlled digitally with the Mobile Station 2 and Central-Station 2 and 3 (not included). Control with the Central-Station 2 and 3 is especially easy by means of track indexing (after carrying out an update), or with different digital central controllers that use the DCC digital format.