A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.

This decoder can be installed in all C Track turnouts with an electric mechanism. The digital formats supported are mfx, Motorola, and DCC. Connections are with plug contacts. An address from 1 to 256 can be set with coding switches.

A digital decoder can be installed simultaneously or later on with the electric mechanism for turnouts. The decoder is simply connected with plug contacts and it can be given a custom address for each turnout (Address 1 to 256). Tools or special knowledge is not required for the installation. The digital current supply can be taken directly from the train operation contact for the turnout. This gives you a finished digital turnout that is immediately ready for use on temporary layouts.

The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts.

The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders.

With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. 

The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts

The LokPilot 5 micro DCC is a "pure-bred" DCC decoder with 14 to 128 speed steps and 2- or 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically.

The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly".

The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors.

The LokPilot 5 micro DCC is a "pure-bred" DCC decoder with 14 to 128 speed steps and 2- or 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically.

The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly".

The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors.

The LokSound 5 micro DCC decoder is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles.

All LokSound 5 micro DCC decoders are equipped with a Next18 interface. This decoder also includes the adapter board with wire harness.

The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts.

Please note that these LokSound 5 micro DCC decoders does NOT come with a speaker.

ESU 50210 ECoS 2.1 - ESU Command Station
6A, 7" TFT colour display - 120V

The ECoS 50210 is already the second generation of our successful ECoS command station. With the latest ECoS command station, ESU continues to offer state-of-the-art digital technology combined with contemporary functional range and easy handling all this for a fair price-performance ratio.

The ECoS has - like most of the recent central stations - a large coloured display with high resolution. In combination with its ground-breaking and easily operated user interface and excellent contrast values of the coloured screen, ECoS reaches unprecedented ergonomics: unlike all the other central stations, the ECoS can be also operated without a stylus - all symbols and writings are hugely marked and clearly structured.

The LokPilot 5 micro DCC is a "pure-bred" DCC decoder with 14 to 128 speed steps and 2- or 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically.

The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly".

The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors.

The new ESU CabControl is a complete DCC system which allow you wireless control of your locomotives, accessories and routes. This system use a handheld with Android operating technology interfaced to your lay-out through wireless LAN. Power supply and a smart technology connector box is all included so you can operate your trains as soon as you hook it up to your layout (assuming that you already have DCC or DCC/sound equipped locomotives).

If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry.

This is a 50 milliliter or 1.67 oz. bottle for refilling all smoke generators. You can find information on hazard warnings and the safety data sheet under Instructions / Operating Manual.

The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl.

LokPilot 5 decoders are offered with all common interfaces

The LokPilot 5 DCC decoder can also be used on analog DC trains. The top speed can be set separately. The decoder switches between the operating modes (DCC / DC) fully automatically "on-the-fly".

The LokPilot 5 Basic is a "pure-bred" DCC decoder.

While LokPilot 5 decoders can undoubtedly meet all requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable.

The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles.

The LokSound 5 micro DCC Direct Kato USA has been specially developed for installation in track N vehicles of the Kato USA brand: Most diesel locomotives of this manufacturer are installed in the American model of these decoders instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder.

The LokSound 5 micro DCC Direct Kato USA with its dimensions of 60.0mm x 10.1mm is a pure DCC decoder and comes without a loudspeaker.

The LokPilot 5 is a real multi-protocol decoder.; DCC as well as Motorola®, Selectrix® and M4.

In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values ​​on the main track can be read out with suitable control centers.

Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are available.

The LokPilot 5 decoder can also be used in analog DC and AC mode.

Top features of PIKO SmartControl Light…

• SmartControl Light is an affordable and easy-to-use digital system
• Fully NMRA-DCC compatible.  Works with all brands of DCC decoders.
• Maximum output of 2 Amps.
• Operation is and easy and intuitive.
• Control and store up to 9,999 locomotives with up to 24 functions per loco
• One built-in reversing loop output.
• Control up to 20 locos at a time!

The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl.

LokPilot 5 decoders are offered with all common interfaces

The LokPilot 5 DCC decoder can also be used on analog DC trains. The top speed can be set separately. The decoder switches between the operating modes (DCC / DC) fully automatically "on-the-fly".

The LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations.

Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. The M4 protocol supports the automatic registration on mfx® compatible central units.

The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts.

The LokSound 5 decoder can reproduce up to 10 channels simultaneously.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

What the LokProgrammer can do:

The LokPilot 5 is a real multi-protocol decoder.; DCC as well as Motorola®, Selectrix® and M4.

In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values ​​on the main track can be read out with suitable control centers.

Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are available.

The LokPilot 5 decoder can also be used in analog DC and AC mode.

North American Version
Retail: $229.95 USD
 
A complete DCC starter system in the palm of your hand! Includes many of the features of the NCE Powerhouse PH-PRO, but at a lower price. Operates up to 6 trains plus extra cabs. Wireless compatible. Includes 120/230V power supply.

With its unique design the LokSound 5 Direct DCC can easily replace boards that provide poor motor control, low volume, or generally inferior sound. Not only will the decoder work fine with most factory installed speakers, but it will sound even better with our new 11x15mm “sugar cube” speaker and sound enclosure kits.

If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester V2.0: Plugged into the side of the Decoder Tester V2.0 it enables you to comfortably test all large scale decoders.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.

The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker.

The LokSound 5 micro is actually a "small miracle": With a footprint of 21mm x 10 mm it is by far the smallest LokSound decoder, which we have ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. These LokSound 5 micro decoders are equipped with a Next18 interface.

Adapter plugs are available (sold separately) to suit all popular digital interface types. See below for decoders with adapter plus included.

With our new modular speaker baffle set you can easily assemble your tailormade speaker baffle suitable for two miniature speakers. Both – diameter and height – can be individually adapted to suit your needs. Considerable audio pressure and excellent sound fidelity can be generated by employing two speakers wired in parallel.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

This loudspeaker module is suitable for large H0, O or OO gauge diesel locomotives or steam locomotives with tenders. Its built-in passive radiator, in conjunction with the built-in full-range speaker, results in good bass reproduction without compromising the high and mid range sound frequencies. This module is an excellent alternative for those who like deep bass but are not dependent on extreme volume. The speaker is a perfect match with the LokSound 5 and LokSound 5 L decoders.

This is a large refill bottle with 250 ml / 8.45 oz. for all smoke units and for 1 Gauge models with cylinder steam. You can find information on hazard warnings and the safety data sheet under Instructions / Operating Manual.

With a width of 9mm, this rectangular loudspeaker is slim enough to fit small H0 or N-gauge models. Despite its small dimensions, volume and sound are surprisingly balanced. The speaker comes with a matching sound chamber and is a real alternative wherever there is no space for a larger speaker.

Article No. 6646
120 Volt Transformer. 32 VA. UL tested

The track voltage can be adjusted between 5 and 17 volts (AC). The accessory voltage is 17 volts (AC).

Plastic housing. Dimensions 140 x 120 x 80 cm / 5-1/2" x 4-3/4" x 3-1/8". UL tested.

Only for indoor use.

The NEW LokSound 5 DCC Direct, with integrated PowerPack, can easily replace boards that provide poor motor control, low volume, or generally inferior sound. Not only will the decoder work fine with most factory installed speakers, but it will sound even better with our new 11x15mm “sugar cube” speaker and sound enclosure kits (seold seperately). Worried about dead spots or pesky yard ladder switches? With the unique design and engineering there’s no need as we’ve built in the ESU PowerPack direct into the decoder!

The LokPilot 5 micro DCC is a "pure-bred" DCC decoder with 14 to 128 speed steps and 2- or 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically.

The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly".

The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors.

Mobile Control II Remote Control single Handset for ECoS, german / english. With lanyard and USB-cable

The Mobile Control II applies the WLAN standard for communicating with the ECoS. The Mobile Control II can control all locomotives registered in the ECoS. All important locomotive properties such as name, symbol, function mapping as well as symbols for function buttons will be taken from the ECoS and will be displayed correctly. All accessories and routes displayed on the control panel of the ECoS can be switched. Of course the differentiation between double, treble and quadruple aspects will remain fully intact and displayed with the correct symbol on the display.

The LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations.

Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. The M4 protocol supports the automatic registration on mfx® compatible central units.

The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts.

The LokSound 5 decoder can reproduce up to 10 channels simultaneously.

Connect ECoSBoost/Navigator to ECoS with this 7-Pin Mini-Din plug on 6-Pin Mini-Din plug.

The 21 MTC adapter board is suitable for digitising a loco without interface and for the case you do not intend to wire the decoder freely.

ESU's new adapter board 3 for decoders with 21MTC interface is best suited for everyone intending to digitise a loco without interface but with many functions without having to carry out major soldering work.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.

The LokSound 5 micro DCC Direct has been specially developed for installation in Spur N vehicles of the Atlas and Intermountain brands: it can be inserted directly instead of the analog board installed there as standard. However, the decoder can also be used for similar models from other manufacturers at your own discretion.

The LokSound 5 micro DCC Direct with its dimensions of 66.0mm x 8.2mm is a pure DCC decoder and comes without a loudspeaker.

Digital Starter Set with Oval of Track | Trix

Article No. 11100 - N scale

Digital Starter Set with N-scale oval of track and Mobile Station.

This switched mode power pack is for connecting to and supplying power to the Märklin 60114 or 60116 Track Box but suitable for many other applications requiring power compatible with this unit.

The input is 120 volts / 60 Hertz

The output 18 volts / 36 watts DC voltage. 

Dimensions 85 x 55 x 74 mm / 3-3/8" x 2-1/8" x 2-7/8".

Connections: Hollow socket 5.5/2.5 mm, positive conductor inside.

The switched mode power pack is authorized for use as a toy and comes in a plastic housing. The 66367 switched mode power pack is designed for use only indoors.

The LokPilot 5 DCC is a "pure-bred" DCC decoder. with 14 to 128 speed steps and 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl.

LokPilot 5 decoders are offered with all common interfaces

The LokPilot 5 DCC decoder can also be used on analog DC trains. The top speed can be set separately. The decoder switches between the operating modes (DCC / DC) fully automatically "on-the-fly".

"MKL" for Märklin by ESU; Many newer Märklin locomotives and some British locomotives with a 21-pin interface, may not adhere to the standard design of the 21MTC interface. These locomotives require amplified signals at the AUX3 and AUX4 outputs which you will get with "MKL" decoders.

The LokPilot 5 is a true multi-protocol decoder.; DCC, Motorola®, Selectrix® and M4.

Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are available.

"MKL" for Märklin by ESU. Many newer Märklin locomotives and some British locomotives with a 21-pin interface, may not adhere to the standard design of the 21MTC interface. These locomotives require amplified signals at the AUX3 and AUX4 outputs which you will get with "MKL" decoders.

The LokPilot 5 decoder can also be used in analog DC and AC mode.

This is a receiver for switching turnouts, signals, and uncoupler tracks. The m83 supports the digital formats Motorola, DCC, and mfx. The digital address can be set by means of coding switches or by means of the programming track in 4 steps. 

This is a Multi Protocol digital hand control unit for both DCC and mfx locomotives and accessories. 40 locomotives can be controlled with direct access*. Up to 32 locomotive functions and 320 solenoid items can be controlled

NOTE: The 66955 is the controller (only). You will also need the track connector box (60116) and a power adapter (66367)

This is a switched mode power pack for connections to and supplying power to the 60216, 60226 Central Station as well as the 60213-60215 Central Station and the 60175 and 60174 Boosters. Output 19 volts / 60 watts AC voltage or 15 volts / 50 watts DC voltage (can be switched with a slider switch). This is a tabletop switched mode power pack. It comes in a plastic housing. The unit has mounting tabs. Dimensions 116 x 72 x 65 mm / 4-9/16" x 2-13/16" x 2-9/16". Connections: 4-pin mini DIN high current plug. The 60045 switched mode power pack is designed only for use in dry areas.

The LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations.

Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. The M4 protocol supports the automatic registration on mfx® compatible central units.

The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts.

The LokSound 5 decoder can reproduce up to 10 channels simultaneously.

The LokSound 5 micro DCC decoder is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles.

All LokSound 5 micro DCC decoders are equipped with a Next18 interface. This decoder also includes the adapter board with wire harness and a 8-pin NEM plug.

The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts.

Please note that these LokSound 5 micro DCC decoders does NOT come with a speaker.

A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.

This set is the ideal way to start out in Digital Control (DCC and mfx). It includes a Trix Mobile Station control system which is easy to use in both DCC and mfx. If you are using locomotives with mfx protocol the controller will automatically recognize and load the profile of the locomotive (Name, Class, Icon, Address, Function buttons and more). All you need to do is place the locomotive on the track. In DCC mode you have full control of the CVs and can build and store your own locomotive profile. Up to 40 profiles can be stored for direct access.

This set can be expanded with the Trix C Track extension sets and with the entire Trix C Track program

Code 83: The rail profile is 2.1 mm / 0.083" high