Athearn GENESIS (HO) DC-21 Pin Motherboard for LEDs (3)
Athearn - HO scale - GENESIS
DC-21 Pin Motherboard for LEDs (3)
HobbyTech has an extensive stock of digital controllers, decoders and accessories including power supplies, wires, adapter boards, conversion kits. Our primary brands are ESU, Marklin, PIKO but also stock other lines.
There are 154 products.
Athearn - HO scale - GENESIS
DC-21 Pin Motherboard for LEDs (3)
For Kato N-Scale Budd RDC.
Your locomotives look like the real thing. The Digitrax Locomotion System makes them run like the real thing, too!
DS51K1 Stationary Decoder For Single Kato Unitrack Turnouts, easy cost effective way to add DCC control to your Kato Unitrack Turnouts.
power adapter: 15V - 21V / 5A
Input: 120-240 VAC (Euro and US cables)
The stabilized 90VA power supply has more than enough power for most applications. The output voltage can be selected using the potentiometer ranging from 15V to 21V and is therefore suitable for all gauges.
The ECoS (ESU Command Station) is so powerful and capable that many model railroaders would like to replace their present digital station with an ECoS. It is now possible to connect your controllers like Digitrax® and Uhlenbrock® handheld throttles directly to the ECoS, thanks to the ESU L.Net Converter. Additionally, you can continue to use your feedback devices which support the well-known Loconet® communication protocol
Mobile Control II Remote Control single Handset for ECoS, german / english. With lanyard and USB-cable
The Mobile Control II applies the WLAN standard for communicating with the ECoS. The Mobile Control II can control all locomotives registered in the ECoS. All important locomotive properties such as name, symbol, function mapping as well as symbols for function buttons will be taken from the ECoS and will be displayed correctly. All accessories and routes displayed on the control panel of the ECoS can be switched. Of course the differentiation between double, treble and quadruple aspects will remain fully intact and displayed with the correct symbol on the display.
ORDER NOW - and get an EXTRA 5% Advance Order Discount - (deducted from the price below)
ESU 50220 ECoS 2.5 - ESU Command Station
6A, 7" TFT colour display - 120V
The ECoS 50220 is already the second generation of our successful ECoS command station. With the latestECoS command station, ESU continues to offer state-of-the-art digital technology combined with contemporary functional range and easy handling all this for a fair price-performance ratio.
The new ESU CabControl is a complete DCC system which allow you wireless control of your locomotives, accessories and routes. This system use a handheld with Android operating technology interfaced to your lay-out through wireless LAN. Power supply and a smart technology connector box is all included so you can operate your trains as soon as you hook it up to your layout (assuming that you already have DCC or DCC/sound equipped locomotives).
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
A very important part of the LokSound system is the speaker. Therefore, we only use specially developed loudspeakers geared to the sound decoder. Here we recommend the following old saying, the bigger the speaker, the better the sound. As such, we offer loudspeakers in various sizes, one of them will surely fit into your loco. Should there not be enough space, you can also install the speaker in a ‘ghost waggon’ directly behind the loco.
With our new modular speaker baffle set you can easily assemble your tailormade speaker baffle suitable for two miniature speakers. Both – diameter and height – can be individually adapted to suit your needs. Considerable audio pressure and excellent sound fidelity can be generated by employing two speakers wired in parallel.
With our new modular speaker baffle set suitable for a single miniature speaker you can easily assemble your tailormade speaker baffle for two miniature speakers. Both – diameter and height – can be individually adapted to suit your needs. Even with one speaker the audio pressure is considerably better than with one circular speaker intended for these dimensions.
With a width of 9mm, this rectangular loudspeaker is slim enough to fit small H0 or N-gauge models. Despite its small dimensions, volume and sound are surprisingly balanced. The speaker comes with a matching sound chamber and is a real alternative wherever there is no space for a larger speaker.
This loudspeaker module is suitable for large H0, O or OO gauge diesel locomotives or steam locomotives with tenders. Its built-in passive radiator, in conjunction with the built-in full-range speaker, results in good bass reproduction without compromising the high and mid range sound frequencies. This module is an excellent alternative for those who like deep bass but are not dependent on extreme volume. The speaker is a perfect match with the LokSound 5 and LokSound 5 L decoders.
This new speaker module fits wherever 20mm x 40mm rectangular speakers were previously installed. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves significantly improved bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders.
This loudspeaker module is suitable for large tenders with gauge H0 or OO or models with gauge 0. Its built-in passive radiator, in conjunction with the built-in broadband speaker, results in good bass reproduction without neglecting the highs and mids. Especially for diesel or steam locomotives, this module is a real alternative for those who like deep bass but don't need extreme volume. The speaker fits perfectly with our LokSound 5 or LokSound 5 L decoders.
This new speaker module fits wherever 20mm x 40mm rectangular speakers were previously installed. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves significantly improved bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders.
This speaker module offers extremely good performance data with moderate dimensions. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves high quality bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders.
This round speaker module can replace a regular 28mm round speaker in most cases. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves high quality bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders.
Visaton loudspeakers offer a powerful bass and a high-quality audio playback, whereas ESU loudspeakers are also suitable for open-land vehicles due to their plastic membrane.
If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry.
Our SwitchPilot decoders cannot only control point mechanisms but also daylight signals. Most modern signals are equipped with LEDs. Usually the anode connections of multi-aspect signals are combined in order to reduce the number of wires. Some manufacturers (e.g.: Viessmann®) combine the cathodes and for that reason these signals could not be controlled with the SwitchPilot in the past. Our new adapter provides the solution. Simply plug the adapter into the output terminals of the SwitchPilot and you are ready to go.
SwitchPilot V3.0, accessory decoder for 4 twin coils magnetic, 2 x Servo, DCC/MM, 1A
SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons..
SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Servo has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price.
If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
Perfect for Athearn (and others) this new 9 pin (female) 21MTC (Male) adapter board allows the popular 6 output ESU 21MTC LokSound and LokPilot decoders to be easily added to your favorite locomotive.
ESU's new adapter board 3 for decoders with 21MTC interface is best suited for everyone intending to digitise a loco without interface but with many functions without having to carry out major soldering work.
ESU's new adapter board 3 for decoders with PluX22 interface is best suited for everyone intending to digitise a loco without interface but with many functions without having to carry out major soldering work.
With our small relay, loads are controllable whose draw exceeds the decoder’s function output. Put the relay between output and load.
Many railcars are equipped with a ski at both ends. In order to function correctly in block sections, and braking timely in front of red signals, it is vital for the decoder to employ only one ski for (voltage) pick up – depending on direction of travel.
The 21 MTC adapter board is suitable for digitising a loco without interface and for the case you do not intend to wire the decoder freely.
The 21 MTC adapter board 2 is also suitable for digitising a loco without interface. It is very helpful, if you do not intend to wire the decoder freely or if you wish to use more than four function outputs on your LokPilot or LokSound decoder. This adapter board simulates the typcial size and shape of Märklin® 6090x-decoders and can be installed in every suitable position.
If you own a loco with a PluX jack and would like to install a normal decoder with an 8-pin NEM652 plug? No problem, you just need the ESU PluX adapter board.
With this expansion board you can easily expand your LokPilot V4.0 or LokSound V4.0 decoder (with 21MTC interface!): All you need to do is to plug the decoder onto the expansion board and benefit from using 4 additional function outputs (AUX5 through AUX8) for lighting effects, coupler etc. In addition, you are able to connect 2 RC-servos!
Adapter board, 18-pin Next-18 socket to PluX12, Flex, 88mm
This adapter board can be docked to all decoders with Next18 connector and offers a PluX12 interface on the locomotive side. The Flex PCB can be folded and extended to length almost as desired. The adapter board comes with shrink tubing and speaker connection cables.
The Next18 adapter board is suitable if you want to digitize a very small locomotive without a digital interface, but do not want to hard-wire the decoder. The board is extremely small with dimensions of only 13.0 mm x 9.0 mm. The mounting tabs can also be broken away for tighter fit applications. Functions AUX3 and AUX4, logic outputs, are both amplified (each about 180mA). In total, up to 6 outputs can be used.
Soldered connection cables with a length of approx. 20 cm.
Dimensions: Length 13.0 mm x 9.0 mm (With mounting tongue: 18.0 mm x 9.0 mm).
What the LokProgrammer can do:
Affordable, robust, high quality DCC decoder for standard requirements.
The LokPilot Standard decoder generates 0.9A continuous current and easily handles all commonly available DC motors as well as coreless motors. The LokPilot Standard can also be used on analogue DC layouts. The LokPilot Standard decoder has four function outputs
The new LokPilot Fx Nano is the perfect function decoder for vehicles without a motor offering little space for a decoder but with features such as interior lighting or directional headlights.
If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester V2.0: Plugged into the side of the Decoder Tester V2.0 it enables you to comfortably test all large scale decoders.
The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders.
With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds.
The LokSound 5 Fx is a special edition of the LokSound family. It has no motor output and is specially designed for use in cab control cars and other cars that require sound but do not have a propulsion (motor) themselves.
..........................................
HobbyTech can load your preferred sound file.
The LokSound decoder is ready for your choice of prototypical sound. It is preloaded with a basic sound file intended for testing only.
First Step: Add your decoder to the Shipping Cart
Second Step: Visit these links to select and add the sound file suitable to your locomotive:
== LokSound 5 North American and Australian Sound files
== LokSound 5 European Sound files
Want to do it yourself?
Get your own LokProgrammer and add a new dimension to your hobby.